Softcam.cfg

Post Reply
User avatar
oscamlover
Technical Force
Technical Force
Posts: 1899
Joined: 27 Aug 2013, 1:07 pm
Location: india

Softcam.cfg

Post by oscamlover » 13 Sep 2013, 10:49 am

# SoftCam EMM Log configuration

#

# Save EMM data

# 00 Don't save anything (default)

# 01 Save processed EMMs (/var/tmp/emmproc.bin)

# 02 Save rejected EMMs (/var/tmp/emmblock.bin)

# 03 Save both EMMs
L: { 00 }


# Check additional OSC Frequency !!! ONLY FOR DBOX2 !!!

# 00 No Check (default)

# >0 Check on, Value in KHz , example 8MHz=08000
F: { 00 }


# Check additional Baurate for ATR !!! ONLY FOR DBOX2 !!!

# 00 No Check (default)

# >0 Check on, Value in bit/s, example 81861
B: { 00 }


# Enable TPScrypt Support

# *0 TPScrypt off

# *1 TPScrypt on (default)

# 1* don't use PTS on Viaccess cards

# 2* don't use PTS on Cryptoworks cards

# 3* don't use PTS on Viaccess and Cryptoworks cards

Y: { 01 }


# Empty RS232 buffer before writing

# 00 No reset

# 01 Reset Buffer (default)
E: { 01 }


# SoftCam Blocker/Filter definition

#

# 00 = Allow EMM (default for all)

# 01 = Block EMM addressed to:

# all card

# | shared address/provider

# | | unique address/hex_serial

# ----------------------------------

I: { 00 00 00 } ****** All SA UA

V: { 00 00 00 } Via - SA UA

S: { 00 00 00 } Seca - SA UA

N: { 00 00 00 } Nagra All SA UA

C: { 00 00 00 } Crypto All SA UA

O: { 00 00 00 } Conax - SA UA

D: { 00 00 00 } NDS All SA UA


# Timeout Definitions

#
T: { 00 02 01 } ATR timeout (normal*X), instruction timeout (normal*X)


# com1/com2 delays, all delays to be entered in decimal !

#

# Do NOT touch !!!!!!!!!!!!!!!!!!

# all timings should be 0, change only if you have problems.

T: { 01 00000 000 } ****** : byte delay (1e-6 s), instruction delay (1e-3 s)

T: { 02 00000 000 } Seca

T: { 03 00000 000 } Viaccess

T: { 04 00000 000 } Nagra

T: { 05 00000 000 } CryptoWorks

T: { 06 00000 000 } Geldkarte

T: { 07 00000 000 } Conax

T: { 08 00000 000 } NDS

T: { 09 00500 000 } Dreamcrypt/Firecrypt


# Use Crypto card bug to decode any CW, no matter of chid

#

# Cxxx configuration (is aktiv for the provider only if a config line is present)

# (ECM sample to be used to get the cw's with Cxxx)

#

# Provider provider chid - that is present on the card for that provider

# || || || ||

# Use constant CW's for

# caid pid
CW0 ...
CW1 ...

<ATTENTION FOR NEW MEMBER>
->AUTHENTICATION AS PM, URL LINK OPEN AFTER 10-12 POST
->NEVER USE SPAM ,ONLY SMILIES OR WORLDS LIKE "THANKS,NICE INFO TYPE"
->NEVER USE MOBILE NUMBERS,EMAIL OR OTHER WAY OF CONTANT


Post Reply