NCAM 2.0 NEW FIX COMPILED AND PATCHED BY MAROUAN
- Shahid Geo
- Moderator
- Posts: 9897
- Joined: 16 Jun 2013, 9:51 pm
- Has thanked: 6409 times
- Been thanked: 3208 times
NCAM 2.0 NEW FIX COMPILED AND PATCHED BY MAROUAN
How to install?
Open dcc past this in to tmp folder
After go to telnet
Command to install in telnet
opkg install /tmp/*.ipk
- Shahid Geo
- Moderator
- Posts: 9897
- Joined: 16 Jun 2013, 9:51 pm
- Has thanked: 6409 times
- Been thanked: 3208 times
-
- Gold Contributor
- Posts: 1090
- Joined: 19 Jun 2013, 3:19 pm
- Location: █║▌│█│Teh Lachi Distt Kohat║█║▌│█
- Has thanked: 20 times
- Been thanked: 39 times
NCAM 2.0 NEW FIX COMPILED AND PATCHED BY MAROUAN
Dear Shahid Geo,
Kia ye Sports 24 koi ziada khas channels hai jo log is ke peche pare hai?
Kia ye Sports 24 koi ziada khas channels hai jo log is ke peche pare hai?
NCAM 2.0 NEW FIX COMPILED AND PATCHED BY MAROUAN
Hi friends.
Yesterday i put hand to install NCam software in my clone dm800se through DCC296. i managed to connect the dcc but telnet was not connected. in the process of trouble shouting my dm800se rebooted and failed to come up again. so i had to find the new image for installation without success. i downloaded many images which all were not compatible. In all this I was using windows8 computer. Can any one help me get fist the compatible image for my stb and step by step procedure of installing the Ncam by using dcc and a router. Thanks.
NCAM 2.0 NEW FIX COMPILED AND PATCHED BY MAROUAN
any response?Arselona wrote: ↑05 Oct 2017, 10:46 am
Hi friends.
Yesterday i put hand to install NCam software in my clone dm800se through DCC296. i managed to connect the dcc but telnet was not connected. in the process of trouble shouting my dm800se rebooted and failed to come up again. so i had to find the new image for installation without success. i downloaded many images which all were not compatible. In all this I was using windows8 computer. Can any one help me get fist the compatible image for my stb and step by step procedure of installing the Ncam by using dcc and a router. Thanks.
- Shahid Geo
- Moderator
- Posts: 9897
- Joined: 16 Jun 2013, 9:51 pm
- Has thanked: 6409 times
- Been thanked: 3208 times
NCAM 2.0 NEW FIX COMPILED AND PATCHED BY MAROUAN
You install open pli 4 or 6 install thwn inatall new version of ncam
NCAM 2.0 NEW FIX COMPILED AND PATCHED BY MAROUAN
I first of all determine the the bootloader and sim type of my box, only to find that it is sim2.2 with boot loader SSL88a. I searches online for openpli image with bootloader ssl88 and found the compatible openpli 6.0. Thereafter i connected my box to the router via ethenet cable and my computer to the same router via wlan. Then i pressed and held the flashup button of my box and while putting on the power button until the lcd displays the ip address. I then opened my google chrome pasted the address to flash the image. after flashing is complete i just shut down the box for 30 seconds na turned on to reboot successfully. I did not use anything other than this.Arselona wrote: ↑16 Oct 2017, 4:01 pmany response?Arselona wrote: ↑05 Oct 2017, 10:46 am
Hi friends.
Yesterday i put hand to install NCam software in my clone dm800se through DCC296. i managed to connect the dcc but telnet was not connected. in the process of trouble shouting my dm800se rebooted and failed to come up again. so i had to find the new image for installation without success. i downloaded many images which all were not compatible. In all this I was using windows8 computer. Can any one help me get fist the compatible image for my stb and step by step procedure of installing the Ncam by using dcc and a router. Thanks.
Who is online
Users browsing this forum: Apple, Claude, Google, Google Adsense, raotariq, Yandex and 4 guests