why mgcamd crash after fiew minuts in vu solo?

User avatar
taree
Senior Registered Member
Senior Registered Member
Posts: 894
Joined: 01 Aug 2013, 3:32 pm
Has thanked: 686 times
Been thanked: 417 times

why mgcamd crash after fiew minuts in vu solo?

Post by taree »

i have vu solo.
cccam works flawless but mgcamd creating probelm.
i manually install vu mgcamd1.35a but nothing is opening.
i think mg-cfg is the problem.
here is mg-cfg details which i downloaded from their addons.
---------------------------------------------------------
# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 02 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 00 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30

# network ecm timeout in seconds
K: { 05 }

# newcamd dead routes connect retry, sec
Q: { 600 }

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 03 } 172.16.1.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 06}

# map all 180x nagra caids to 1801
# default is 01
F: { 01 }
---------------------------------------
my question is which values i should change to get ecm from my cccam?
i have a cline.
VU ZERO 4K
WETEKPLAY2
SAMSUNG 40K5000
sohaillinks
Junior Member
Junior Member
Posts: 2
Joined: 20 Aug 2013, 11:26 pm

Re: why mgcamd crash after fiew minuts in vu solo?

Post by sohaillinks »

save and reboot box

Code: Select all

# EMM messages
#    00 don't show any EMMs (default)
#    01 show only valid EMMs
#    02 show valid and bad EMMs with complete data display
M: { 02 }

# ECM messages
#    00 don't show anything about ecm
#    01 normal mode, show pids processed, decoded ecm and cw
#    02 verbose mode, show valid and bad ECMs with data
C: { 02 }

# AU
#    00 disable, no emm pids processed
#    01 enable, emm pids always processed for soft-au and shared cards
#    02 auto, emm started only if channel cant be decoded
#    03 process emm pids for network cards update only
A: { 01 }

# key update (sum 01 or 02 with 04)
#    01 update only new keys, default setting
#    02 update all keys (used for valid PMK checking)
#    04 enable TPS au
#    + tps SID, which pmt pid contains au pid
U: { 01 }

# config files folder (softcam, autoroll, ignore/priority)
#    00 files in /var/keys
#    01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
#    00 no network (default)
#    01 newcamd netclient
#    02 radegast netclient
#    04 camd3 netclient
#    08 gbox netclient
#    32	cccamd netclient, card list saved as /tmp/cccamd.info 
#    	(ECM only, supported server version up to 2.1.1, later not work)
G: { 32 }

# network retry, use summ for several options
#    00 disable
#    01 retry every new ecm
#    02 try to connect to offline shares every Q: seconds
#    04 try to detect and fast reconnect to lost (and not used atm) server
#    + XX messages number and YY seconds to reconnect
#    mg will reconnect to server, if no answer to last XX ecm/keepalive or
#    if no answer for last ecm or keepalive sent for YY seconds
#    set to 0 to disable
N: { 07 } 5 00

# network ecm timeout in seconds
K: { 02 }

# newcamd dead routes connect retry, sec
Q: { 10 }

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 02 }

# on screen display type
#    00 No OSD (default)
#    01 neutrino
#    02 enigma
#    03 relook
#    + user password for http auth
O: { 00 } username password

# on screen display Options, summ of:
#    01 show emu ecm 
#    02 show network shares messages
#    04 show decoding failed / fta
#    08 show emm keys update
#    + web port to use for osd
S: { 03 } 80

# Log option, summ of:
#    00 off
#    01 network udp log
#    02 log to console
#    04 file, appended ! delete it by yourself, before it eat all your hdd
#    + IP udp-port log-file-name
L: { 02 } 172.16.1.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value, 
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
#    00 Off (default)
#    01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
#    02 Ecm data cache, remember CW for (E:) time 
#    04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 00 }

# reread files, summ of: 
#    00 No (default)
#    01 reread config file on channel change (including priority and ignore, but not replace/cache)
#    02 reread SoftCam.Key on channel change
#    04 reread SoftCam.Key if file changed
R: { 04 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 00 }

# map all 180x nagra caids to 1801
# default is 01
F: { 00 }
User avatar
Golden
Vip
Vip
Posts: 4648
Joined: 14 Jun 2013, 6:00 am
Location: Pakistan
Has thanked: 1301 times
Been thanked: 671 times

Re: why mgcamd crash after fiew minuts in vu solo?

Post by Golden »

@ taree

Strange Bro Because I Was Thinking That U 've Knowledge To Handle Such Basic Queries As U R Also A Server Holder !

:prescription:

@ sohaillinks

Bro Don't Mention Your Personal Analysis Or Settings Because It May Leads The Client To Breakage & Chances Of This Disturbance Are

Quite Brighter !

:ring:
User avatar
taree
Senior Registered Member
Senior Registered Member
Posts: 894
Joined: 01 Aug 2013, 3:32 pm
Has thanked: 686 times
Been thanked: 417 times

Re: why mgcamd crash after fiew minuts in vu solo?

Post by taree »

thanks brother for ur response
i will try ur given configuration and will post result later.
VU ZERO 4K
WETEKPLAY2
SAMSUNG 40K5000
User avatar
taree
Senior Registered Member
Senior Registered Member
Posts: 894
Joined: 01 Aug 2013, 3:32 pm
Has thanked: 686 times
Been thanked: 417 times

Re: why mgcamd crash after fiew minuts in vu solo?

Post by taree »

golden bhai
u r misunderstood
server holder is taree65...i m only taree
dont have any server..only client
VU ZERO 4K
WETEKPLAY2
SAMSUNG 40K5000
User avatar
Golden
Vip
Vip
Posts: 4648
Joined: 14 Jun 2013, 6:00 am
Location: Pakistan
Has thanked: 1301 times
Been thanked: 671 times

Re: why mgcamd crash after fiew minuts in vu solo?

Post by Golden »

@ taree

sohaillinks Has Given U The Value :

[code]G: { 32 }[/code] By Which U 'll Be Connected To CCcam Only !

U Should Put :

[code]G: { 33 }[/code] For Both NewCamd & CCcam. Some DrawBacks & Still There*

Don't Touch The Default Values Of Your "mg_cfg" Until Tweaking !

:ring:

*Topic Moved To The Card-Sharing Section .

:flag1:[/red]
User avatar
Golden
Vip
Vip
Posts: 4648
Joined: 14 Jun 2013, 6:00 am
Location: Pakistan
Has thanked: 1301 times
Been thanked: 671 times

Re: why mgcamd crash after fiew minuts in vu solo?

Post by Golden »

@ taree

U Should Read The Topic Also : http://golden-mgcamd.net/viewtopic.php?f=12&t=896#p6104" onclick="window.open(this.href);return false;
User avatar
taree
Senior Registered Member
Senior Registered Member
Posts: 894
Joined: 01 Aug 2013, 3:32 pm
Has thanked: 686 times
Been thanked: 417 times

Re: why mgcamd crash after fiew minuts in vu solo?

Post by taree »

ok master here is the update after ur suggestion
now conecting to my cccam server and getting ecm
but the problem is that after fiew minuts and watching fiew chanells
mgcamd crash and dont open any chanell.
but the chanells which i see before crash are opening but new one dont open
but on every chanell i can see ecm info showing from server
and also encryption icon becoming green...very strange
first i think that it is because of dishtv tweaking.
then i restarted cam and go to dialogtv in ******.
same result..5 to 6 chaells open then cam crashed ant no new chanell open..previous ones
watcable and new ones showing ecm but blank screen.
also with hotbird i get same result...
i also use one cline in cccamd.list instead of many.
i m using black hole 2..5 version
try pli and vti images also..tried mgcamd 1.38 and 1.35a
but result are the same..
i m very disapointed after using enigma2.
now its upto you masrter if u can solve my problem.
VU ZERO 4K
WETEKPLAY2
SAMSUNG 40K5000
User avatar
kami2k
Gold Contributor
Gold Contributor
Posts: 1287
Joined: 16 Jun 2013, 7:42 pm
Location: Muzaffarabad - Azad Kashmir
Has thanked: 42 times
Been thanked: 9 times

Re: why mgcamd crash after fiew minuts in vu solo?

Post by kami2k »

Dear ftp to user/keys/ and change the permission of files to 775. Read+write All, it will hopefully fixed
.....(¯`v´¯)
..... ·.¸.·´
...¸.·´
.. (
☻/
/▌
/ \ Spread LOVE and PEACE . Press "Thanks" ♥

Intel 8700K |CM |GIGABYTE Z370|G.SKILL Ripjaws 16GB |SSD 256GB,8TB|Gigabyte GTX 1050 2GB|CM 750W|46" Samsung|VU+ SOLO2:UNO
User avatar
taree
Senior Registered Member
Senior Registered Member
Posts: 894
Joined: 01 Aug 2013, 3:32 pm
Has thanked: 686 times
Been thanked: 417 times

Re: why mgcamd crash after fiew minuts in vu solo?

Post by taree »

waiting dear golden for ur kind suggestion plz
VU ZERO 4K
WETEKPLAY2
SAMSUNG 40K5000

Who is online

Users browsing this forum: No User AvatarBytespider [Bot], No User AvatarClaude [Bot], No User AvatarDot [Bot] and 11 guests